RADDEP

RADDEP

0 Posts
0 Followers
0 Following
Follow Following Following
2 months ago
Joined
Arizona, USA
7.25” / 18.42 cm Wrist

Recent Comments

commented on Watch this if you want to change the Bezel on your Kamasu! ·

I almost never post to any sites, but I felt I needed to write this one. I just purchased an Orient Kamasu, version one, model RA-AA0004E39B. I purchased it from Amazon. As I was researching the watch and its Pro’s and Con’s I came across the mods for bezel and bezel insert. The bezel (coin edge) model B16-P can usually be had from Long Island watch (https://longislandwatch.com/), but they were out of that model. They do have other models in stock. I did find that model for sale from “Serious Watches” from the Netherlands, (https://www.seriouswatches.com/?country=US). It was more expensive for shipping, but I wanted it right away. I ordered the green ceramic luminous bezel (Green Ceramic Luminous Bezel Insert (#C27) from Long Island watch (https://longislandwatch.com/). It looks like a great match for my Kamasu. Of course you order what goes with your watch. Most of the items I will describe can be purchased from Amazon.

So, I purchased the Kamasu model RA-AA0004E39B and proceeded to purchase the other parts for the bezel and insert replacement. I did a lot of research on how to remove the bezel. Almost everyone stated how difficult it was to remove and the chances are you will do damage to your case and or destroy the original bezel. I continued to look on YouTube, forums, and any sight that had information on bezel removal. This is the method I used. I will try to list the tools and the way I removed the bezel. I have to say I was very surprised and happy with the way things worked out.

First, I removed the original bracelet so I could change that out for a FKM rubber strap (WOCCI 22mm Ventilated Watch Band, FKM Rubber, Silver Buckle (Army Green). The lug width is 22mm and the buckle end is 20mm. The original clasp can’t be used so I used the buckle that came with the Kamasu.

Secondly, I feel it’s very important to tape up the watch. I use (Selizo High Temp Tape, 5 Pack Multi – Sized 1/8”, 15/64”, 15/64”, 15/32”, 5/64”, Heat Resistance Up to 280℃ (536℉)). I used a wider piece to cover the bezel and the case at the 6 o’clock position. I creased the tape as deeply as I could into the very tight space between the bezel and case. I used different size tape to protect the lug, sides and bottom just to be safe. The tape is really good. It sticks well but comes off easily without leaving residue.  I did not go out and buy any kind of special bezel tool remover. After doing my research I decided to use the razor knife method to remove the bezel.

Next, place your watch into a good holder for stability. I used a JOREST hard plastic case holder. Make sure you tape it up even with a non-marring holder. Trust me, I had to do a little buffing up even using a hard plastic holder. I placed the watch, so it was perpendicular to the desktop so the 6 o’clock position was pointing up. With the case holder and your hand, the watch was stable in that position.

At this point I used an X-acto #18 blade, used the same tape from above and put two pieces over the blade end. It only adds a tiny amount of thickness to the blade.

Now, you are ready to try to remove the bezel. With the watch secure in the holder with the 6 o’clock position pointed upward. Place the taped # 18 blade in the groove you made with the tape. I used magnifying glasses (whatever brand you like) to see as well as you can for that groove. Hint, make sure you have pressed that tape into the gap as well as you can. It gives you a clearer look at the very small space and protects the watch case and bezel. Carefully place the # 18 blade into the groove space. Keeping everything secure and stable start gently tapping on the end of the #18 blade. I used a regular Jewelrs hammer. I used the Jorest watch hammer. Most of the tools you need for your watch needs come in the JOREST Watch Repair Kit +. It’s a good kit for hobbyists watch enthusiasts. So far it has worked well for me for all my needs. Be careful and accurate with your strikes. You may have to hit a little harder once you get the blade to stay in the groove. Consistent steady blows to the end of the blade. Try to keep everything lined up so you are hitting straight down into the groove. If needed increase striking force a little at a time. Don’t go crazy hard, you will end up missing the blade or getting offline which will damage the case and or bezel. I took a few good steady blows keeping everything lined up and finally the blade slipped deeper into the groove space. At that point there was a fairly good size gap to use a Jorest case back opening tool with the small narrow tip. It went into the groove opening easily. Then with a very slight turn of the tool the bezel came right off.

I can’t tell you how happy I was with this technique. It worked very well without any damage to the case and only the very, very minor scuff on the very bottom of the bezel. Which buffed out easily so you would never tell.  Now I’m just waiting for the new bezel and insert to arrive.

I hope this helps you and gives you a little confidence to try this yourself. I was really scared to try this myself, but I love tinkering with my watches. My suggestion is to try this or any different method you think will work but be slow and cautious and if you just can’t get the bezel off take it to a professional before you destroy your watch.

commented on Removing kamasu bezel ·

I almost never post to any sites, but I felt I needed to write this one. I just purchased an Orient Kamasu, version one, model RA-AA0004E39B. I purchased it from Amazon. As I was researching the watch and its Pro’s and Con’s I came across the mods for bezel and bezel insert. The bezel (coin edge) model B16-P can usually be had from Long Island watch (https://longislandwatch.com/), but they were out of that model. They do have other models in stock. I did find that model for sale from “Serious Watches” from the Netherlands, (https://www.seriouswatches.com/?country=US). It was more expensive for shipping, but I wanted it right away. I ordered the green ceramic luminous bezel (Green Ceramic Luminous Bezel Insert (#C27) from Long Island watch (https://longislandwatch.com/). It looks like a great match for my Kamasu. Of course you order what goes with your watch. Most of the items I will describe can be purchased from Amazon.

So, I purchased the Kamasu model RA-AA0004E39B and proceeded to purchase the other parts for the bezel and insert replacement. I did a lot of research on how to remove the bezel. Almost everyone stated how difficult it was to remove and the chances are you will do damage to your case and or destroy the original bezel. I continued to look on YouTube, forums, and any sight that had information on bezel removal. This is the method I used. I will try to list the tools and the way I removed the bezel. I have to say I was very surprised and happy with the way things worked out.

First, I removed the original bracelet so I could change that out for a FKM rubber strap (WOCCI 22mm Ventilated Watch Band, FKM Rubber, Silver Buckle (Army Green). The lug width is 22mm and the buckle end is 20mm. The original clasp can’t be used so I used the buckle that came with the Kamasu.

Secondly, I feel it’s very important to tape up the watch. I use (Selizo High Temp Tape, 5 Pack Multi – Sized 1/8”, 15/64”, 15/64”, 15/32”, 5/64”, Heat Resistance Up to 280℃ (536℉)). I used a wider piece to cover the bezel and the case at the 6 o’clock position. I creased the tape as deeply as I could into the very tight space between the bezel and case. I used different size tape to protect the lug, sides and bottom just to be safe. The tape is really good. It sticks well but comes off easily without leaving residue.  I did not go out and buy any kind of special bezel tool remover. After doing my research I decided to use the razor knife method to remove the bezel.

Next, place your watch into a good holder for stability. I used a JOREST hard plastic case holder. Make sure you tape it up even with a non-marring holder. Trust me, I had to do a little buffing up even using a hard plastic holder. I placed the watch, so it was perpendicular to the desktop so the 6 o’clock position was pointing up. With the case holder and your hand, the watch was stable in that position.

At this point I used an X-acto #18 blade, used the same tape from above and put two pieces over the blade end. It only adds a tiny amount of thickness to the blade.

Now, you are ready to try to remove the bezel. With the watch secure in the holder with the 6 o’clock position pointed upward. Place the taped # 18 blade in the groove you made with the tape. I used magnifying glasses (whatever brand you like) to see as well as you can for that groove. Hint, make sure you have pressed that tape into the gap as well as you can. It gives you a clearer look at the very small space and protects the watch case and bezel. Carefully place the # 18 blade into the groove space. Keeping everything secure and stable start gently tapping on the end of the #18 blade. I used a regular Jewelrs hammer. I used the Jorest watch hammer. Most of the tools you need for your watch needs come in the Jorest Watch Repair Kit +. It’s a good kit for hobbyists watch enthusiasts. So far it has worked well for me for all my needs. Be careful and accurate with your strikes. You may have to hit a little harder once you get the blade to stay in the groove. Consistent steady blows to the end of the blade. Try to keep everything lined up so you are hitting straight down into the groove. If needed increase striking force a little at a time. Don’t go crazy hard, you will end up missing the blade or getting offline which will damage the case and or bezel. I took a few good steady blows keeping everything lined up and finally the blade slipped deeper into the groove space. At that point there was a fairly good size gap to use a Jorest case back opening tool with the small narrow tip. It went into the groove opening easily. Then with a very slight turn of the tool the bezel came right off.

I can’t tell you how happy I was with this technique. It worked very well without any damage to the case and only the very, very minor scuff on the very bottom of the bezel. Which buffed out easily so you would never tell.  Now I’m just waiting for the new bezel and insert to arrive.

I hope this helps you and gives you a little confidence to try this yourself. I was really scared to try this myself, but I love tinkering with my watches. My suggestion is to try this or any different method you think will work but be slow and cautious and if you just can’t get the bezel off take it to a professional before you destroy your watch.