MarcusDLG

Marcus

5 Posts
15 Followers
6 Following
Follow Following Following
1 year ago
Joined
Fort Worth, TX, USA
5.75” / 14.61 cm Wrist

Recent posts

CW Bel Canto at Windup Watch Fair in Dallas

I finally got to try on a Bel Canto at the Windup Watch Fair in Dallas this weekend. I've always liked the look of this watch, but I always assumed it...
3 comments

Another Successful Omega Restoration

I've just finished restoring this Omega Seamaster Calendar that I bought a few months ago. I serviced the movement and replaced the crystal. I also ad...
4 comments

Just finished the service on this Omega

I bought this Omega about a month ago and I've finally had time to give it a service myself. It turned out very nice, I really like the dial on this o...
2 comments

Recent Comments

commented on Any info re this Omega pls? ·

If you open the back, the movement will have a serial number on it and you can put it in a decoder to get the date of manufacture. Just take some precautions when opening the case back, this watch does look like it has radium lume. https://serial-number-decoder.com/omega/omega.htm

commented on Omega Experts? ·

The 3 probably fell off and was replaced with a generic indice. Without better photos, it's hard to tell if it's a fake. I would think it probably isn't since it wouldn't make sense to fake an incorrect indice. That being said, since it's missing the second hand and has that incorrect indice, it's probably got some more issues that you can't see. I would treat it as a donor watch for parts and wouldn't pay more than $75 for that watch alone.

commented on Replacement Mainspring question ·

The main dimension that you don't want to mess with is the height. If the height is a lot smaller, it won't wind evenly and could cause more wear. You should also never get a mainspring that is thicker, although a slightly thinner one could work. Since I'm assuming you don't have mainspring winders, you also want to make sure the diameter of the mainspring is smaller than your actual barrel so that you can push it in.

The one that you found seems to be a really good match, so I don't think it would cause any issues. I wouldn't worry about the .02mm difference in height and the slightly shorter length will affect the power reserve, but probably not by much. Good luck and have fun!

commented on Hesalite or Sapphire for Speedmaster Moonwatch Professional? ·

I'm saving up for a Speedmaster so I've been having this debate in my head for a while now. I think the Hesalite looks better and personally I don't have any concerns about damaging it. However, I prefer the polished bracelet links on the sapphire version and I also really want the display caseback. If I had to make a decision today, I would probably go with the sapphire, but I'm going to try them both on before I make the final purchase.

commented on Looking to get into repair/restoration ·

I always clean the screws. Honestly, I doubt it really makes much of a difference, but that seems to be standard practice.

As far as keeping track of the screws, whenever I remove something from the movement I place the screws for that object next to it. Once everything it disassembled, I take some pictures of the disassembled parts so that I can see which screws go with which sections of the movement. It helps to have a tray with some dividers so that you can keep related things together.

Once you do it a few times, you start to get a good idea of which screws go where. It's actually not as hard as you would think. Calendar & Automatic works tend to complicate the screw situation which is why I would recommend avoiding them at first. 

commented on How concerned are you with wearing radium watches? ·

Another update: I've been playing around with my Geiger counter some more and discovered something interesting. While the reading from the dial side is around 1800 CPM on my Omega, the back of the watch only measures about 200 CPM. The movement and the case back seem to block most of the radiation from reaching your wrist.

commented on Looking to get into repair/restoration ·

I had also heard the advice to start with pocket watches, but I chose to go straight to wristwatches since I have little interest in pocket watches. I think watching watch repair videos prepared me very well.

As far as brands, I really like Hamilton because they tend to have simple movements and can be had for reasonable prices. Any brand will probably be ok but stick to 17 jewel hand wind movements with no calendar works at the beginning. Also be aware that any watch with lume from the mid-60's and before will likely be using radium, which requires some extra precautions. Best to avoid those for now.

My best advice is to take lots of pictures when disassembling the movement. Also, don't get discouraged if a part goes flying across the room and you can't find it, that's part of the experience 😂. Have fun!

More posts

Will you buy vintage watches with engraved case backs?

I have bought several vintage watches with engraved case backs. I think it's kind of cool. It shows that each watch has it's own story. However, I can see how some people would feel weird wearing a wa...
133 votes ·
13 comments

How concerned are you with wearing radium watches?

I'm an amateur watchmaker and I've recently picked up a 1960 Omega Seamaster to restore. However, this is the first time I will be working with a radium dial and hands. I've got a Geiger counter comin...
117 votes ·
14 comments